1. Hello and Welcome to The Quality Forum Online...Continuing in the spirit of People Helping People !
    Dismiss Notice
Dismiss Notice
You must be a registered member in order to post messages and view/download attached files in this forum.
Click here to register.

calibration

  1. JohnDoe
    Thread

    Laborscope and evidence that the measuring devices have been calibrated

    Hello. I am rather new in the ISO topics. We are implementing ISO 9001:2015 at the moment. Can someone please give me an answer do I need the...
    Thread by: JohnDoe, May 18, 2018, 2 replies, in forum: ISO 9001:2015 - Quality Management Systems
  2. Pfrice
    Thread

    Calibration requirements for Cable Analyzer

    Hi everybody, For test equipment like a Cable Analyzer (Fluke DSX 5000), is there any reason we need to get “initial condition found” of the...
    Thread by: Pfrice, Mar 9, 2018, 7 replies, in forum: ISO 9001:2015 - Quality Management Systems
  3. Troy M
    Thread

    Gauge calibration

    My company is divided into divisions, some ISO certified others not. If a certified division does some work for one of the non certified divisions...
    Thread by: Troy M, Mar 1, 2018, 2 replies, in forum: ISO 9001:2015 - Quality Management Systems
  4. Al Weisenborn
    Thread

    Grace Periods in Calibration and Maintenance Intervals

    Good morning Al, I do not have a question about TrackPro. We are having an internal discussion here and I was wondering what your thoughts were....
    Thread by: Al Weisenborn, Feb 26, 2018, 5 replies, in forum: Coffee Break and Community Discussion Forum
  5. Sergio Rufini
    Thread

    Calibration of thermometers

    Hello, I have a doubt about the calibration of the single thermometers. In our labs we have a measurement system for test composed of: Agilent...
    Thread by: Sergio Rufini, Aug 9, 2017, 5 replies, in forum: ISO 17025 - Calibration and Test Laboratories
  6. Jonathan
    Thread

    Calibration for plain Ring Gages

    What is the standard procedure for a proper calibration of a ring gage? Thank you kindly
    Thread by: Jonathan, Jun 23, 2017, 2 replies, in forum: Gage Calibration and Uncertainty
  7. omengramirez
    Thread

    Comparison Between Z540.3 and Mil-STD-45662

    To the Admin, Thank you very much for putting this online forum, ever since Elsmar closed it was very difficult to look for information and...
    Thread by: omengramirez, Mar 28, 2016, 4 replies, in forum: ISO 17025 - Calibration and Test Laboratories
  8. chris2pher
    Thread

    Hello to the community

    I 'fell' into calibration 6 years ago and the elsmar cove was a great source of info to me, always learning as I didn't 'grow up' in calibration....
    Thread by: chris2pher, Mar 8, 2016, 1 replies, in forum: New Member Introductions
  9. Mark Paul
    Thread

    Calibration Work Instructions - Template Needed for Audit

    PLEASE LOCATE ME IN PROPER THREAD. Need Work Instructions for Calibrations of Calipers, Micrometers, etc. We have an AS9100C Audit this...
    Thread by: Mark Paul, Mar 2, 2016, 2 replies, in forum: Gage Calibration and Uncertainty
  10. BradM
    Thread

    FAQ for calibration

    This discussion began on the Ohio Bay Specialists (OBS) LinkedIn site. So since I have the ability to edit/ clean things up here, I would like to...
    Thread by: BradM, Dec 16, 2015, 19 replies, in forum: ISO 17025 - Calibration and Test Laboratories
  11. Evan Balcaen
    Thread

    7.1.5.2 Measurement Traceability

    Hi Everyone, Sorry in advance for the long post! I have recently been tasked with learning ISO, becoming our new Quality Manager and preparing us...
    Thread by: Evan Balcaen, Nov 25, 2015, 8 replies, in forum: ISO 9001:2015 - Quality Management Systems
  12. Mark Paul
    Thread

    CMM and Master Ring Calibration

    Hard to understand, but there is a push in a certain 150 emp company with ±2000 ring gages from 1/2 inch to 18" wants to "calibrate" our ring...
    Thread by: Mark Paul, Nov 13, 2015, 2 replies, in forum: Gage Calibration and Uncertainty
  13. Chris Glover
    Thread

    Linear scales...

    (in the other world known as rulers)... We have many instances where a "scale" is called out as the gage used to confirm product quality. How...
    Thread by: Chris Glover, Aug 24, 2015, 11 replies, in forum: Gage Calibration and Uncertainty
Showing results 1 to 13 of 13