1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.
Dismiss Notice
You must be a registered member in order to post messages and view/download attached files in this forum.
Click here to register.

Search Results

Search Again
  1. Plague Doctor
    Thread

    Within specification or out of specfication

    Hello, There is a spec requirement for dimension - 1,3 +/-0,3 mm The measured value is 1,68 mm Is it: 1. within spec because the first...
    Thread by: Plague Doctor, Jun 30, 2017, 1 replies, in forum: Other Quality and Business Related Topics
  2. Plague Doctor
    Post

    Examples of preventive action - PFMEA

    Hi, I need your advice: We have an action: Measurement of first 3 produced pieces after tool adjustment in the beginning of the production batch...
    Post by: Plague Doctor, Jun 8, 2017 in forum: FMEA - Failure Modes and Effects Analysis
  3. Plague Doctor
    Post

    NDC (Number of Distinct Categories)

    Thanks for the answer. For our processes, yes, we take the samples covering the entire tolerance range. We do %GRR to TV and we have good GRR and...
    Post by: Plague Doctor, Sep 14, 2016 in forum: Gage R&R and MSA - Measurement Systems Analysis
  4. Plague Doctor
    Post

    NDC (Number of Distinct Categories)

    Hi all, We have the same problem with "good GRR but bad ndc" when we do a study for molding purchased parts due to their low part variation. 1....
    Post by: Plague Doctor, Sep 14, 2016 in forum: Gage R&R and MSA - Measurement Systems Analysis
  5. Plague Doctor
    Post

    Approaches to creation of control plan

    1.4. uploaded
    Post by: Plague Doctor, May 30, 2016 in forum: APQP and PPAP
  6. Plague Doctor
    Thread

    Approaches to creation of control plan

    Hello, I'd like to get some advices about control plan. The purpose is not to miss mandatory required content but get rid of unnecessary (not...
    Thread by: Plague Doctor, May 30, 2016, 2 replies, in forum: APQP and PPAP
  7. Plague Doctor
    Thread

    PSW declaration

    Hello, in PSW there is following declaration: DECLARATION I affirm that the samples represented by this warrant are representative of our...
    Thread by: Plague Doctor, May 24, 2016, 4 replies, in forum: APQP and PPAP
  8. Plague Doctor
    Post

    Gage R&R Excel Template required

    Can someone share a template of Nested GR&R for non-replicable measurements?
    Post by: Plague Doctor, Mar 16, 2016 in forum: Gage R&R and MSA - Measurement Systems Analysis
  9. Plague Doctor
    Post

    Cm & Cmk

    What I was told this is the same calculation as for Cp & Cpk only the principle of sampling is different. For Cmk you need to produce 50 or more...
    Post by: Plague Doctor, Mar 1, 2016 in forum: Capability - Process, Machine, Gage …
  10. Plague Doctor
    Post

    GRR for destructive test-Crimped terminal pull-out force

    Thanks, but I read this article just before posting here:) I don't have Minitab so I wonder if there is any difference between calculation...
    Post by: Plague Doctor, Jan 22, 2016 in forum: Gage R&R and MSA - Measurement Systems Analysis
  11. Plague Doctor
    Thread

    GRR for destructive test-Crimped terminal pull-out force

    According to customer's requirement we need to perform GRR for conductor pull-out force (wire is being pulled out of crimped terminal using the...
    Thread by: Plague Doctor, Jan 22, 2016, 4 replies, in forum: Gage R&R and MSA - Measurement Systems Analysis
  12. Plague Doctor
    Post

    GRR - Are out of spec. parts allowed / needed ?

    Thanks for answers. But that is why I asked: in fact our process is quite stable, we are able to produe parts e.g. with range 40% from the range...
    Post by: Plague Doctor, Jan 22, 2016 in forum: Gage R&R and MSA - Measurement Systems Analysis
  13. Plague Doctor
    Thread

    GRR - Are out of spec. parts allowed / needed ?

    Hello, Is it allowed to use samples with out of spec. values for GRR study? Thanks!
    Thread by: Plague Doctor, Jan 20, 2016, 4 replies, in forum: Gage R&R and MSA - Measurement Systems Analysis
Showing results 1 to 13 of 13
Search Again